Page 1 of 2
B407 latest installer (supports v4)
Posted: Sat Feb 24, 2018 5:21 pm
by doodlebug
vA1.180224
B 407 Update with P3Dv4.2 Compatibility
Please back up any liveries and run the uninstaller first.
New MVAMS
New Nightlighting in P3D V4
New 3D sound Module
Updated Addon Menu
Re: B407 latest installer (supports v4)
Posted: Sat Feb 24, 2018 8:15 pm
by FireRx
Re: B407 latest installer (supports v4)
Posted: Sat Feb 24, 2018 8:41 pm
by VetteDrvr
Just saw this. Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you Thank you!!!
Re: B407 latest installer (supports v4)
Posted: Sat Feb 24, 2018 9:07 pm
by Chuck Jodry
Happy to have up at last , it was complicated to update these .
Please list the Sim and what panel selection is being used with any issues reported
Best CJ
Re: B407 latest installer (supports v4)
Posted: Sat Feb 24, 2018 10:55 pm
by VetteDrvr
Got it, installed it, works fine and dandy in 4.1 and many many thanks! I really appreciate what you guys did!
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 4:39 am
by didlam
Hello and thank you again for this beautiful Helos.
In my opinion, it is one of the best on the market. Very good quality and perfect finish.
Regarding the remarks to report to you: I have problems with the additional windows of the panel: that we call with the keys SHIFT + 1, +2, +3 etc ....
The 1st SHIFT + 1 opens nothing !
and the following open windows all black.
for example if I added in the MAMS 'RXP 430/530', the open windows have the correct names but are empty/Black (name: "Reality XP GNS 430 WAAS-RXP_CONFIG_TOOL - DO NOT CHANGE")
In any case thank you for the work you have provided ... beautiful prospects of flights in sight ...
Didier
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 8:09 am
by sunjunkiesi
You will only see something in those windows if you have the relevant add on.
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 9:02 am
by didlam
how does one get these falling add on?
where can we get them?
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 9:14 am
by Krazycolin
You buy them from F1, Mindstar or RXP
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 9:16 am
by didlam
OK thanks for the info
and what about the SHIFT + 1 module configuration? what is it?
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 4:20 pm
by N4GIX
didlam wrote:OK thanks for the info
and what about the SHIFT + 1 module configuration? what is it?
That is the default command for a 2d panel, which is not configured for any of our products any longer.
Re: B407 latest installer (supports v4)
Posted: Sun Feb 25, 2018 7:50 pm
by FireRx
hey Guys,
since everything is in MVAMS now, can I delete that old Milviz folder on the root with the old MV_MM.exe Menu in there without causing issues??
Thanks.
Re: B407 latest installer (supports v4)
Posted: Mon Feb 26, 2018 6:08 am
by JonathanBleeker
Yes
Re: B407 latest installer (supports v4)
Posted: Mon Feb 26, 2018 3:26 pm
by Chuck Jodry
That is a pre update legacy entry that was used for selecting the additional elements like FLIR and Pilot now controlled by the MVAMS , I will need to look through the cfg and weed out any remaining in the 32 something panel.cfgs used in this between 32 and 64 bit versions .
Best CJ
Re: B407 latest installer (supports v4)
Posted: Tue Feb 27, 2018 7:05 am
by didlam
Hello and thank you for this beautiful helo B407
I am adapting my PANEL Hardware to work on both the B407 and the MD530.
But I can not find the name of the Lvariables to use to enable/disable the 'Fuel Boost 1' and '2' and 'Hydraulic Command'
(as I did with the MD530 with a FSUIPC macro: for example for the start pump: "L: cap10 = Tog").
Could you tell me their name please?
Didier