New installers [Resolved]
-
- Posts: 129
- Joined: Mon May 25, 2015 1:36 pm
New installers [Resolved]
Thanks for these
All planes flying except PC Porter
Installs but crashes sim on final as plane appears on screen
Tried default settings in P3D
Tried default avionics
Using P3D vers 5.1.12.26829
Anything else I could try?
xxd09
All planes flying except PC Porter
Installs but crashes sim on final as plane appears on screen
Tried default settings in P3D
Tried default avionics
Using P3D vers 5.1.12.26829
Anything else I could try?
xxd09
-
- Posts: 19
- Joined: Sat Oct 22, 2016 4:44 pm
Re: New installers
On P3D v2HF1 & PC6 carked at end of Scenario load up (CTD)
Where in Support Forums did you get Beaver & Otter v5 files? I can't find them.
B52
Where in Support Forums did you get Beaver & Otter v5 files? I can't find them.
B52
- Slayer
- Posts: 1517
- Joined: Sat Mar 08, 2014 3:26 am
- Contact:
Re: New installers
A couple of tips - Don't use any WX radio stack , you will get a CTD.
The PC-6 uses a LOT of VRAM and that cannot be fixed, in my experience 6GB will barely do it, 8GB is ideal. You can disable Trueglass, that can help a bit.
The PC-6 uses a LOT of VRAM and that cannot be fixed, in my experience 6GB will barely do it, 8GB is ideal. You can disable Trueglass, that can help a bit.
- Slayer
- Posts: 1517
- Joined: Sat Mar 08, 2014 3:26 am
- Contact:
Re: New installers
I don't show you as a registered user of the Beaver and Otter so you can't see those support sections. If you email me your purchase details to steve@milviz.com I can verify and give you access.
-
- Posts: 129
- Joined: Mon May 25, 2015 1:36 pm
Re: New installers
64 .0 GB Installed Ram
2080 TI Graphics Card 11GB GDDR6
Should be enough
xxd09
2080 TI Graphics Card 11GB GDDR6
Should be enough
xxd09
-
- Posts: 19
- Joined: Sat Oct 22, 2016 4:44 pm
Re: New installers
Will doSlayer wrote: ↑Wed Aug 04, 2021 9:12 pmI don't show you as a registered user of the Beaver and Otter so you can't see those support sections. If you email me your purchase details to steve@milviz.com I can verify and give you access.
Thanks
B52
-
- Posts: 129
- Joined: Mon May 25, 2015 1:36 pm
Re: New installers
Finally got her in the air -all Flight1 avionics working -after many uninstalls and reinstalls
Why ? what did I do?
Remains a mystery
xxd09
Why ? what did I do?
Remains a mystery
xxd09
- Slayer
- Posts: 1517
- Joined: Sat Mar 08, 2014 3:26 am
- Contact:
Re: New installers
Even though the installer will run with admin privilege's - on some peoples system it may not due to high UAC settings or antivirus so everything doesn't get installed properly. It's always a good idea to right click/run as admin so the installer can do it's job. Also run your MVAMS as admin - if you don't changes may not save properly either, if you had a GPS stack with WX it would have led to a crash.
Glad you got her flying.
Glad you got her flying.
-
- Posts: 129
- Joined: Mon May 25, 2015 1:36 pm
Re: New installers
Yes that must have been my problem
I did my final install from a download where Anitivirus and Firewall were disabled
The final uninstall was done by running installer and using the “Remove” option ie a clean uninstall
So using very best practice it worked
Usually I do all this as per your advice but was more particular this last time
I always use Admin Privilege
Just took more care with the Porter!
xxd09
I did my final install from a download where Anitivirus and Firewall were disabled
The final uninstall was done by running installer and using the “Remove” option ie a clean uninstall
So using very best practice it worked
Usually I do all this as per your advice but was more particular this last time
I always use Admin Privilege
Just took more care with the Porter!
xxd09