Blackbird Sims / Milviz Forum Archive

http://www.milviz.com/Online_products/P ... 171127.zip

CHANGELOG:

• Fuel Flow gauge in P3D is fixed to reflect consumption
• Tail Beacon attached and effect revised to remain in closer proximity to the rudder.
• Cockpit sounds for door seal and fuel pump in order
• C310 Logic for magneto's and startup routine supported in updated panel.cfg

Thank you for the update, it's great to have the fuel flow gauge working now. Unfortunately, the fuel selectors no longer work in the VC, but they do work fine in the pop-up 2D mode. I can live with it, but thought you would want to know.

I did want to know , ill take a look , they were specifically adapted for P3D here.

After looking I find no problems, there was a code update and a drag / wheel control feature added , you see no animations?

What version of P3D are you running ?

Best CJ

Hi CJ

Same problem here, on p3d4.1. As cd says its not a problem, I tend to use the 2d panel anyway as its easier to see.

Did you change the cockpit textures? I'm not sure if its my imagination but it looks so nice in there...

Ooh sorry to keep posting. I think when someone was repairing the altimeter they might have put the number wheels in wrong. In my system the 10,000, 1,000 and 100 feet wheels are stuck on 9.

Chuck Jodry wrote:I did want to know , ill take a look , they were specifically adapted for P3D here.

After looking I find no problems, there was a code update and a drag / wheel control feature added , you see no animations?

What version of P3D are you running ?

Best CJ

I'm running P3Dv4.1. The fuel selector for the right engine won't move at all, not by drag, mouse wheel or mouse click. The left engine selector will move by drag or mouse wheel, but it will not engage on the left main. It only works on the right main and left aux.

I agree with Sunjunkiesi, the altimeter is not working right. When climbing through 1,000 ft., the altimeter jumps to 9,000 ft. At 10,000 ft. it reads 99,000 ft.

Yup, another " me too " here with regards to the Altimeter. P3Dv4.1 here.

cheers

Im also having the altimeter stuck on 9 issue. Apologize if this is an old issue but I also notice overlapping text in the Autopilot panel. Plus I cant arm altitude hold. I cant also click on VS.
The Parking brake animation also seems to have some clipping issues.

Thanks!

What panel selection are you guys using ? there are actually 6 different interior models depending on what sim and panel are used , one of these is evidently having an issue but I cant duplicate it .

Checked 4 and 4.1 with the full model set used in sequence and cant get this to happen , I do know the digital readout and fuel selectors were reanimated to resolve those specific issues in P3D , leaving an old model somewhere is becoming my leading hypothesis and suspect not requiring an uninstall of the previous version was an error on my part .

If someone could give uninstalling and reinstalling it a crack I would appreciate it


Best CJ

Chuck,

This what I am seeing at PAEN. P3DV4.1 750650 panel.







Greg

Milvis GNS, P3Dv4.1. It seems to be linked to the kohlsman knob in some way, as soon as I turn it, the numbers go nuts.

Good luck!

Chuck Jodry wrote:What panel selection are you guys using ? there are actually 6 different interior models depending on what sim and panel are used , one of these is evidently having an issue but I cant duplicate it .

Best CJ

I'm using the GTN750/GNS430.

Checked 4 and 4.1 with the full model set used in sequence and cant get this to happen , I do know the digital readout and fuel selectors were reanimated to resolve those specific issues in P3D , an old model somewhere is becoming my leading hypothesis and suspect not requiring an uninstall of the previous version was an error on my part .

If someone could give uninstalling and reinstalling it a crack I would appreciate it

Best CJ

Chuck Jodry wrote:Checked 4 and 4.1 with the full model set used in sequence and cant get this to happen , I do know the digital readout and fuel selectors were reanimated to resolve those specific issues in P3D , an old model somewhere is becoming my leading hypothesis and suspect not requiring an uninstall of the previous version was an error on my part .

If someone could give uninstalling and reinstalling it a crack I would appreciate it

Best CJ

Chuck,

I did uninstall and then installed fresh before I took the screen shots above.

Greg