Page 1 of 1
Amphibian turbo jumps all over the place.
Posted: Thu Aug 02, 2018 4:19 pm
by two wolves
The DHC 3T turbo amphibian while on land jumps all over the place. Yes I have the last update installed.
Re: Amphibian turbo jumps all over the place.
Posted: Thu Aug 02, 2018 4:35 pm
by YoYo
Didnt notice. Which airport?
FSX/P3D? Parking brake on/off?
Re: Amphibian turbo jumps all over the place.
Posted: Thu Aug 02, 2018 5:17 pm
by Chuck Jodry
Hello Two Wolves. We will need more clues to go on as its not something anybody has seen to date with the Amphibian
What Sim are you using ?
What airport or location precisely ?
Is the location an addon of some sort ?
Are you using an additional ground handling enhancement product from A2A like accusim or other ?
Does it happen always on solid ground at any airport ?
Did you make any modifications to the installed aircraft.cfg's ?
Best CJ
Re: Amphibian turbo jumps all over the place.
Posted: Thu Aug 02, 2018 9:38 pm
by two wolves
Listen. My Beaver and DHC 3 otter. Both work in steam FSX . With no problems at all. The DHC 3T Turbo is just the way I bought it. I fly in FSX scenery only. No addons.
Re: Amphibian turbo jumps all over the place.
Posted: Fri Aug 03, 2018 2:09 pm
by Chuck Jodry
Communication works like this , you talk I listen and then we change places and repeat the process until we understand the problem , its source and its circumstance , without this process we are left without any apparent reason for the problem , its unique to your installation.
With your reply we now know its in SE , that you are using default scenery and that the DHC2 & 3 operate normally , we have narrowed down the possibilities considerably .
Assess the possible influence of a faulty .bgl by booting up on a default runway like KSEA and report if it does or does not jump around.
Attached is an aircraft.cfg for the amphib , try it and see if there is still a problem , back up the original.
I shall check in later to see where we are at in the resolution process.
Best CJ
Re: Amphibian turbo jumps all over the place.
Posted: Fri Aug 03, 2018 8:30 pm
by two wolves
Chuck Jodry wrote: ↑Fri Aug 03, 2018 2:09 pm
Aircraft.zipCommunication works like this , you talk I listen and then we change places and repeat the process until we understand the problem , its source and its circumstance , without this process we are left without any apparent reason for the problem , its unique to your installation.
With your reply we now know its in SE , that you are using default scenery and that the DHC2 & 3 operate normally , we have narrowed down the possibilities considerably .
Assess the possible influence of a faulty .bgl by booting up on a default runway like KSEA and report if it does or does not jump around.
Attached is an aircraft.cfg for the amphib , try it and see if there is still a problem , back up the original.
I shall check in later to see where we are at in the resolution process.
Best CJ
I tryed the file, still the same. I'll fly the Beaver and DHC 3 Otter. turbo is scraped metal. Thanks for trying.
Re: Amphibian turbo jumps all over the place.
Posted: Fri Aug 03, 2018 8:38 pm
by Chuck Jodry
Can you give the default runway at KSEA a test and tell me if it jumps around , also is it anything to do with high wind speeds ? if this were to get 40 knot gusts it would want to fly .
Thanks
Best CJ
Re: Amphibian turbo jumps all over the place.
Posted: Sat Aug 04, 2018 9:44 am
by two wolves
Chuck Jodry wrote: ↑Fri Aug 03, 2018 8:38 pm
Can you give the default runway at KSEA a test and tell me if it jumps around , also is it anything to do with high wind speeds ? if this were to get 40 knot gusts it would want to fly .
Thanks
Best CJ
I tried, still the same. When I bought the turbo otter. it was great. Then I installed the new installer sp1. Then the problems started. I no longer have installed on my computer. I've been in flight simulators . Way back in 1989, So I'm not new to this game.
Re: Amphibian turbo jumps all over the place.
Posted: Wed Sep 12, 2018 2:50 am
by HappySimming
Hi!
It happens if you put too much load in the Milviz MVAMS.
Screenshots attached.
Remove everything in the Milviz MVAMS load section, save it, and try it again.
Re: Amphibian turbo jumps all over the place.
Posted: Wed Sep 12, 2018 3:50 am
by Krazycolin
Well don’t put too much of a load in...
Re: Amphibian turbo jumps all over the place.
Posted: Wed Sep 12, 2018 4:16 am
by HappySimming
two wolves wrote: ↑Sat Aug 04, 2018 9:44 am
Chuck Jodry wrote: ↑Fri Aug 03, 2018 8:38 pm
Can you give the default runway at KSEA a test and tell me if it jumps around , also is it anything to do with high wind speeds ? if this were to get 40 knot gusts it would want to fly .
Thanks
Best CJ
I tried, still the same. When I bought the turbo otter. it was great. Then I installed the new installer sp1. Then the problems started. I no longer have installed on my computer. I've been in flight simulators . Way back in 1989, So I'm not new to this game.
Krazycolin wrote: ↑Wed Sep 12, 2018 3:50 am
Well don’t put too much of a load in...
Hope two wolves try this out and be able to fly the dhc-3t turbo otter.
