Unable to start
-
alrocreation
- Posts: 1
- Joined: Sun Apr 04, 2021 4:29 pm
- Contact:
Unable to start
Hello,
I bought the PC6 for FS2020 from your site yesterday. I had no problem installing it by following the instructions included in the pdf.
Unfortunately after selecting it and the departure airport, I could not start the PC6 even using Ctrl+E.
Also when selecting this aircraft, all my Saiteck modules disconnect and my joystick deactivates!!!. I have no problems with other aircraft such as the Corsair.
Question: why these bugs, would I have forgotten a manipulation?
Thank you for your answer,
Best Regards
Alain (AlroCreation)
I bought the PC6 for FS2020 from your site yesterday. I had no problem installing it by following the instructions included in the pdf.
Unfortunately after selecting it and the departure airport, I could not start the PC6 even using Ctrl+E.
Also when selecting this aircraft, all my Saiteck modules disconnect and my joystick deactivates!!!. I have no problems with other aircraft such as the Corsair.
Question: why these bugs, would I have forgotten a manipulation?
Thank you for your answer,
Best Regards
Alain (AlroCreation)
-
andy.kauffman
- Posts: 6
- Joined: Sat Sep 25, 2021 2:41 am
- Location: Kaneohe, Hawaii
Re: Unable to start
Hi! What happens if you start on the runway? The engines and electronics should be going then - if the aircraft shuts down after 5 or 10 seconds, then it is the DRM (WASM Helper Service) that has a problem and possibly is not starting.This is what I'm experiencing, and MILVIZ said that they should have a fix for us in a few days.alrocreation wrote: ↑Wed Sep 29, 2021 3:59 pmUnfortunately after selecting it and the departure airport, I could not start the PC6 even using Ctrl+E.
Does the Corsair use the same WASM Helper service?
-
Slayer
- Posts: 1517
- Joined: Sat Mar 08, 2014 3:26 am
- Contact:
Re: Unable to start
Ctrl-E does not work with this aircraft. If none of the controls are working then it is likely related to the WASM helper.alrocreation wrote: ↑Wed Sep 29, 2021 3:59 pmHello,
I bought the PC6 for FS2020 from your site yesterday. I had no problem installing it by following the instructions included in the pdf.
Unfortunately after selecting it and the departure airport, I could not start the PC6 even using Ctrl+E.
Also when selecting this aircraft, all my Saiteck modules disconnect and my joystick deactivates!!!. I have no problems with other aircraft such as the Corsair.
Question: why these bugs, would I have forgotten a manipulation?
Thank you for your answer,
Best Regards
Alain (AlroCreation)
-
jgisbertadell
- Posts: 1
- Joined: Sun May 02, 2021 8:08 am
Re: Unable to start
To me the same thing happens to me.
What is WASM Helper Service?
Thanks
What is WASM Helper Service?
Thanks
-
doodlebug
- Posts: 1642
- Joined: Sun Feb 19, 2017 2:49 pm
- Location: LYX>YUL
Re: Unable to start
We are working on a build without the WASM helper.
We will post it first on the PC6 2020 support forum and then do a release. (Notifications by email).
I had hoped to have it ready already, but it is taking a little longer, as we are using this as an opportunity to do some minor fixes at the same time.
We will post it first on the PC6 2020 support forum and then do a release. (Notifications by email).
I had hoped to have it ready already, but it is taking a little longer, as we are using this as an opportunity to do some minor fixes at the same time.