Page 1 of 1
Prepar3D V4.4
Posted: Tue Dec 04, 2018 11:35 am
by Avidean
I am just getting back into Prepar3D and have a fresh install of Windows 10.
I see on the product pages for my Milviz birds that under supported
platforms they are all Prepar3D V4.3.29.XXX
Is it OK to install in V4.4 or should I hold off?
Re: Prepar3D V4.4
Posted: Tue Dec 04, 2018 4:39 pm
by ThomasAH
If you have birds with WX radar, this may cause problems, but you could temporarily disable it in panel.cfg.
Re: Prepar3D V4.4
Posted: Thu Dec 06, 2018 3:37 am
by jabloomf1230
You also need to change this entry in
dll.xml in the folder
C:\ProgramData\Lockheed Martin\Prepar3D v4
...
Code: Select all
<Launch.Addon>
<Name>WXAdvantage</Name>
<Disabled>False</Disabled>
<Path>Modules\MV_WXM.dll</Path>
<DllStartName>module_init</DllStartName>
<DllStopName>module_deinit</DllStopName>
</Launch.Addon>
Change the disabled entry to
TRUE or just delete the whole LaunchAddon.
Re: Prepar3D V4.4
Posted: Thu Dec 06, 2018 8:56 pm
by ssimm1958
tried loading the pa-30 in p3dv4.4 and p3d ctd, so milviz birds will be upgraded to run in p3dv4.4 at some time right? so just dont try to use them till they are upgraded to work in v4.4 right?
Re: Prepar3D V4.4
Posted: Fri Dec 07, 2018 11:18 pm
by Stew
No, not quite. Don't use the Milviz birds with the Wx Radar installed. My 310R Redux runs fine without the Wx Radar.
Re: Prepar3D V4.4
Posted: Sat Dec 08, 2018 3:35 am
by Avidean
Any change we can get one of the Milviz developers to chip in here?
Re: Prepar3D V4.4
Posted: Sat Dec 08, 2018 3:15 pm
by Stew
Another thread, the same answer:
viewtopic.php?f=142&t=10216
Re: Prepar3D V4.4
Posted: Sat Dec 08, 2018 7:42 pm
by Avidean
That might have helped but it appears that I am not allowed to read that forum!
Re: Prepar3D V4.4
Posted: Sun Dec 09, 2018 10:59 pm
by N4GIX
Avidean wrote: ↑Sat Dec 08, 2018 7:42 pm
That might have helped but it appears that I am not allowed to read that forum!
If you own the plane, you have to request access to the official Support Forum for that aircraft. Send proof of purchase to
info@milviz.com
Re: 310R Causes P3DV4 to crash
Post by SnuffyTheMongoose » Mon Dec 03, 2018 5:41 pm
Until the WX is updated, if you choose the version with it in, the 310 will crash.
Re: Prepar3D V4.4
Posted: Mon Dec 10, 2018 11:21 pm
by Avidean
Hmm, I took care of all of that last year. Find it difficult to believe that I left out the the 737-200 since its my number 1 top favorite Milviz Aircraft. Anyway, When I have a minute I'll do it again
Re: Prepar3D V4.4
Posted: Tue Dec 11, 2018 9:55 am
by doodlebug
You are already a member of the 737 support forum
http://milviz.com/forum/viewforum.php?f=86