Blackbird Sims / Milviz Forum Archive

Uninstalled prev version and installed this new one. Aircraft loads fine and appears to be functioning properly. Increase throttles to max and a/c is stuck in place, does not move forward but the airspeed gauge shows gradually increasing airspeed.

Uninstalled this vers and installed previous (3.180412) and the plane flies at it should. Loaded th a/c at the same airport/runway as with the other problematic version.


Harold

Does your system meet the sim's requirements? YES
Did you temporarily disable your anti-virus program during the download process? YES
Before installing did you disable UAC. (User Account Control)? YES
Did you install, and are you running the sim as an admin? YES
Before running the sim did you make sure the FSX/P3D directory is off limits to any AV scanning? YES
Does your system have the required distributables? YES
Is your video card DX11 compatible? YES
If applicable, did you disable any FSX to P3D migration tools (like Estonia) before running the sim? YES
Are you using an aircraft other than a Milviz one as your default aircraft? YES
Have you installed in the root sim directory? YES
Do you have the appropriate SimConnect libraries installed? YES

Aircraft: 310R Redux
Sim platform: P3D v.4
Operating system: Win7
Version: 3.180904
Unique ticket identifier: D836B320-2E01-96E3-46C6-D4010F0F6BD2
Our dedicated

Did you release the parking brakes? If still on, the aircraft will remain in place.

Yes, confirmed the parking brake knob was all the way in (off). Cycled the parking brake. Left it off. Brakes are off though I have no movement of the rudder pedals. Full throttle. Engine rev'd up. The airspeed gradually increased to 100 (before I pulled the throttle back) all while still sitting in the same spot on the runway.

Also cannot slew the aircraft. Tried several airports and different runways.

Is there an anchor that needs to be hauled in? Or maybe there's an anchor AND an airspeed gauge problem???

When the parking brake is set, the following events are set true (lat, long, and attitude. This will prevent slewing. The els{ condition resets those three events to false: Look in the ..\panel\TW_XMLGauge folder, and find the above three lines (line 128, 129, and 130).

Replace the above with this to disable that part of the script. Let me know if it works for you now.

My ..\Lockheed Martin\Prepar3D v4\SimObjects\Airplanes\MV_C310R\panel folder does not have a TW_XMLGauge folder in it.

Did you disable your av prior to downloading and installing?

Shift 3----remove shocks then you`r off

I have the same problem and in addition if I start a flight in the air the aircraft does not move although it makes all the usual in-flight sounds.

I have uninstalled and reinstalled the previous version which works correctly.

AV was disabled during download and install

Krazycolin wrote: ↑

Sat Sep 08, 2018 4:09 am

Did you disable your av prior to downloading and installing?

Yes.

haroldeh wrote: ↑

Sat Sep 08, 2018 4:07 am

My ..\Lockheed Martin\Prepar3D v4\SimObjects\Airplanes\MV_C310R\panel folder does not have a TW_XMLGauge folder in it.

Oops! My Bad. That should have been ..\C310_XMLGauge folder!

N4GIX wrote: ↑

Sat Sep 08, 2018 1:44 pm

haroldeh wrote: ↑

Sat Sep 08, 2018 4:07 am

My ..\Lockheed Martin\Prepar3D v4\SimObjects\Airplanes\MV_C310R\panel folder does not have a TW_XMLGauge folder in it.

Oops! My Bad. That should have been ..\C310_XMLGauge folder!

I found similar (but not exact) code in the C310-Logic.xml file in that folder:

(A:BRAKE PARKING POSITION,percent) 0 >
(A:SIM ON GROUND,bool) and
(L:C310_Chocks,bool) 1 == or
if{ 1 (>K:FREEZE_LATITUDE_LONGITUDE_SET) 1 (>K:FREEZE_ATTITUDE_SET) }
els{ 0 (>K:FREEZE_LATITUDE_LONGITUDE_SET) 0 (>K:FREEZE_ATTITUDE_SET) }

I commented around that code:

<!--
(A:BRAKE PARKING POSITION,percent) 0 &gt;
(A:SIM ON GROUND,bool) and
(L:C310_Chocks,bool) 1 == or
if{ 1 (>K:FREEZE_LATITUDE_LONGITUDE_SET) 1 (>K:FREEZE_ATTITUDE_SET) }
els{ 0 (>K:FREEZE_LATITUDE_LONGITUDE_SET) 0 (>K:FREEZE_ATTITUDE_SET) }
-->

Success! I can now fly the a/c.

Thanks,
Harold

Further checking reveals the aircraft is now defaulting to having the chocks set and they have to be removed before flying. I re-enabled the previous code and removed the chocks and the aircraft will now move -- however, it still begs the question of why the airspeed indicator (and maybe other gauges) think the airplane is moving.

Also amazing how strong those chocks are to hold back a twin engine aircraft at full throttle!


Harold

haroldeh wrote: ↑

Sat Sep 08, 2018 3:02 pm

Also amazing how strong those chocks are to hold back a twin engine aircraft at full throttle!

I coded it this way in order to prevent the aircraft from "running away" when doing mag checks, etc. Brakes in both FSX and P3D don't hold worth a hoot!

I'm sorry I completely forgot that I had coded the system to use chocks also.