Page 1 of 1
MVAMS Does Not Change Anything in UH1 ?
Posted: Wed Nov 13, 2019 9:24 pm
by FlyingJB
Hello all...I tried to make changes to the UH1 Huey using the MVAMS. I make my changes and press Save Defaults button but nothing changes in the Huey.
Am I doing something wrong here ?
Tks...JB
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Wed Nov 13, 2019 9:25 pm
by JonathanBleeker
When you re-open the MVAMS, the settings don't persist?
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 1:21 am
by FlyingJB
Hi JB
Yes the settings are what I set them to in MVAMS but they are not being set in helicopter ?
Thanks
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 9:15 am
by JonathanBleeker
Is your P3D set to run as admin? Right click on it, select properties->compatibility and check Run this program as administrator.
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 12:53 pm
by FlyingJB
Hi JB...I am running FSX and not P3D and I open MVAMS as Admin. I am running FSX on a different drive than the C: dive if that has anything to do with it ?
Tks JB
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 12:53 pm
by FlyingJB
...and FSX is run as Admin also...tks
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 1:25 pm
by JonathanBleeker
That shouldn't affect it.
You are applying the same settings to both the UH-1H and UH-1C modules in the MVAMS?
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 6:44 pm
by FlyingJB
All I see on the MVAMS opening screen is one helicopter picture. I don’t see a way of distinguishing between the UH-1H or UH-1C. Is there an area in there which shows which UH-1 model the changes were made to?
Thanks
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 6:50 pm
by JonathanBleeker
I have linked Dutch to this thread since he is the programmer on this.
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 6:53 pm
by Dutch
FlyingJB wrote: ↑Thu Nov 14, 2019 6:44 pm
All I see on the MVAMS opening screen is one helicopter picture. I don’t see a way of distinguishing between the UH-1H or UH-1C. Is there an area in there which shows which UH-1 model the changes were made to?
Thanks
You should have two separate entries in your MVAMS lineup, one for the UH-1C and another for the UH-1H.
Dutch
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 8:40 pm
by FlyingJB
Fellas..I must apologize as I did not see the scroll down arrow on the screen so I was actually only seeing and updating the UH-1C only and flying the UH-1H
I scrolled down and now I see the UH-1H on the MVAMS and all good now
Sorry to waste your time...thanks
Re: MVAMS Does Not Change Anything in UH1 ?
Posted: Thu Nov 14, 2019 10:46 pm
by Dutch
FlyingJB wrote: ↑Thu Nov 14, 2019 8:40 pm
Fellas..I must apologize as I did not see the scroll down arrow on the screen so I was actually only seeing and updating the UH-1C only and flying the UH-1H
I scrolled down and now I see the UH-1H on the MVAMS and all good now
Sorry to waste your time...thanks
No problem, I'm glad it turned out to be something simple. Hope you enjoy the Huey!
Dutch