Blackbird Sims / Milviz Forum Archive

Posted: **Fri May 10, 2019 9:15 pm**

I just purchase this MD530F having a problem, I load helicopter I pick follow instructions, I pick doors to be on, when I load it in no doors tried several times , I don't understand the following ? delete ALL MLVZ files, place the KMLVZ files into the correct directory under the Milviz directory. any help would be great thanks ranger-buck

Posted: **Sat May 11, 2019 7:32 pm**

HI, ok I disconnected my v c uninstall MD350F THAN REINSTALLED, set the 530 I wanted checked mark doors, loaded prog up and still no doors? and now can not activate radios on? no problem starting no problem flying. again in my last post didn't get ans. to those questions? please advise what I should do next? thanks ranger-buck > You have received a new private message from "doodlebug" to your account
> on
> "milviz.com" with the following subject:
>
> post moved
I just rx this cant fine post move?

Posted: **Mon May 13, 2019 7:43 pm**

Is the configuration manager you are using the new orange and white MVAMS?

Posted: **Tue May 14, 2019 5:47 pm**

hi JonathanBleeker ok I did, I know this configuration manager is different than the one I use back in 2016 when I down loaded this same md350f and bell 407 I was advise by Milviz team to reload the 2016,but I wanted to try this updated one. ok its more cost but I wanted to try it, after I got a new up dated system I added orbx scenery and orther aircraft I also upgraded all those programs . I still would like to work on this problem before giving up. I don't understand the following ? delete ALL MLVZ files, place the KMLVZ files into the correct directory under the Milviz directory. any help would be great. ranger-buck

Posted: **Tue May 14, 2019 5:59 pm**

To be clear, don't buy this model again because all updates have been free whether you buy from us or from somewhere else.

The latest version is available a the top of the forum, MD530 Latest build (fixes elevator trim) 180709

Posted: **Tue May 14, 2019 6:56 pm**

whats this? Re: Milviz MD530F
Report this post was this a mistake doodlebug ? this was a reply to my last post
Quote

Post by doodlebug » Tue May 14, 2019 4:59 pm

To be clear, don't buy this model again because all updates have been free whether you buy from us or from somewhere else.

The latest version is available a the top of the forum, MD530 Latest build (fixes elevator trim) 180709

Posted: **Tue May 14, 2019 7:06 pm**

Seems to be some confusion.

I don't want to sidetrack the conversation, but we didn't mean you to reload the 2016 version

Posted: **Wed May 15, 2019 5:42 pm**

hi again, well ok sorry that were not doing to well on this problem, I was going to order the dvd but already have too much money invested. so I cant used the program the way it is. please direct me to who can make the refund back to paypal. thank you

Posted: **Wed May 15, 2019 6:42 pm**

I think if you can give Jon the information he asked for, that we can resolve your problem.
If you have the latest build installed you should have the MVAMS desktop icon. When you open it you should see something similar to the image below. Can you confirm:

: MVAMS-530-.png (264.04 KiB) Viewed 1181 times

Posted: **Thu May 16, 2019 7:56 pm**

hi and no it doesn't show that . it comes up with a screen that shows what to pick, not the one from 2016 . is it possible that you could send me the down load instead the one from pilot shop? . what shows orange strip on top pic of 530 on left below that all the line up of different names like black magic n20at etc 16 different names, on the right general than controls you would check mark the controls you want or not page 1 now page 2 aircraft state i pic doors n cold and dark . click save defaults . AM not a comp tech as you can tell from all my post sorry, ok hope we can work this out....thank you for trying to help. ranger-buck

Posted: **Thu May 16, 2019 9:46 pm**

is it possible that you could send me the down load instead the one from pilot shop

Download it here:
http://www.milviz.com/Online_products/P ... 180709.zip

Posted: **Thu May 16, 2019 10:34 pm**

http://www.milviz.com/Online_products/P ... 180709.zip I down loaded came up the same, and of course I did the disconnect of virus and orther as instructed. ? am going to try another way

Posted: **Fri May 17, 2019 11:36 am**

Can you post a screenshot of what you are seeing? Press Print Screen on your keyboard, then go to MS Paint and press Ctrl V. Save the image and post.

Posted: **Fri May 17, 2019 7:44 pm**

hello JonathanBleeker, ok think this will work, see attached fsx.jpg file ranger-buck

Posted: **Sat May 18, 2019 7:31 pm**

I hope this helps, the image is diferent from yours . can you send me the instruction manual again, I think I have the wrong one thanks