Flight course [Resolved - User calibration issues]

[alioskycm84]

Hello, I really don't know what to do much less than think but since the last update I have not been able to get my plane to fly correctly, it is a problem from waypoint to waypoint, it never manages to make the correct flight, it starts going round and round until I find the right again waypoint, attached FD image...

[Slayer]

It almost looks like you didn't cross a waypoint and it's trying to circle back? Do you have this problem on all flights or just this specific FPL?

[alioskycm84]

It is in all the FPLs, I have not been able to make a complete flight. It almost always happens when I activate the NAV button, while with HDG that does not happen, it is only in NAV mode. Because when I deactivate the NAV, it stops doing this problem and when I activate it again, a two maybe three waypoint passes but later it deviates the flight course again.

[ccmh15]

On the FMS, open the LEGS page and make sure on the top right, "SEQUENCE: AUTO" is selected (and not "INHIBIT").

This setting might automatically get set to INHIBIT, whenever you have DISCONTINUITYs in your flight plan, so always make sure your FPL handling is correct.

Cheers,
Chris

[Slayer]

Good call , that one has gotten me a few times also.

[alioskycm84]

My course problems go on and on they don't stop bothering me, I'm configuring everything right but every time I touch any control in mid-flight because everything is screwed up, it's like it starts circling at the same point looking for the fix, this is the route by car and everything, look at the photos ... Thank you

[alioskycm84]

picture

[admin9]

I had this issue when i first bought the plane. I found it was duplicate assignments of yoke controls. Make sure there are no duplicates.

[alioskycm84]

Where can I check the duplication of the assigned controls? Something is happening because it is something strange, the FD goes to one side and the Course stays to another, the only thing that corrects is using the HDG because when I activate the NAV the problem begins, that is, it is the NAV that gives me these pains of head...

[alioskycm84]

What is this, even when my God, I do not know how many things I am going to do, what happens with this, the HDG button is what corrects the course while the NAV if I touch another control button deviates the course

[Slayer]

Where can I check the duplication of the assigned controls?

What he means is if you had an axis in P3D settings duplicate it can cause issues with autopilot. If it sends unwanted input it can cause autopilot to not work correctly.

[alioskycm84]

Double check the controls and or I think I have problems, I really don't know what happens, in the beta versions this never happened to me, look at another screenshot

[Slayer]

The last 3 screen shots you posted it does not show previous waypoints or the line connecting to your current waypoint which makes me think you have a discontinuity in your flight plan. I'm asking the devs to take a look to see where you could be going wrong.

[Slayer]

I need you to please double check that there are no duplicate mapped flight controls especially between Prepar3d and/or FSUIPC if you use that. It really seems this must be the case as it happens when you touch your controls and things break. Also check if you have a "jitter" or spike in an axis as this can cause issues too. The NAV mode is sensitive to control issues where the HDG is not.(from a developer)

Another possibility is that if you are creating a flight plan in P3D also? the AP mode may try to follow that.

Questions from the developers:

Does the aircraft always circle the waypoint when you are in NAV mode?
Does it happen going from HDG to NAV ? What the exact sequence you are switching modes
Does it always turn opposite of the FD?
When this happens does it still maintain altitude or just drift uncontrolled?

The more information you can provide the better or if you can make a video that would also help.

[alioskycm84]

Hello, thank you for your support;
If I have the FSUIPC installed in my Sim, but I do not have configured controls of my Yoke GF-PRO Yoke System from GoFlight Co. I have the axes configured directly in the controls of my P3Dv 4.5, the calibration is correct, I do it periodically through USB GAMING CONTROLLES in Windows.
I DO NOT create the flight plans in the P3D, I use the PFPx and I do not care about anything to the FMC, I assure you that discontinuity of the FMC is not, I assure that because I check the legs very well before starting each flight.

For developers:
1-Does the aircraft always circle the waypoint when you are in NAV mode?
A: This happens at all times, it is like something is activated automatically and it is not only in the waypoints, the same happens in the climb, cruise that in approach that is to say at any time can happen, sometimes it begins when it intercepts the waypoints.
2-Does it happen going from HDG to NAV? What the exact sequence you are switching modes.
A: No, not at all, this happens by itself, from the moment I activate the NAV button, the HDG button responds correctly, and even when you reactivate NAV it is impossible for it to correct the course and start going round and round in it. point.
3-Does it always turn opposite of the FD?
A: Yes, it always turns to the right, I have never seen it turn to the left, everything always starts to the right, the FD (Cyan color) always tries to find the correct course, but the other (Black color) goes to the right otherwise and there is the conflict. The plane always goes to the black arrow on the PFD while trying to correct with the cyan arrows on the FD.
4-When this happens does it still maintain altitude or just drift uncontrolled?
A: Never lose attitude, always keep stable at the moment you are, the same Climb, Course, Approach.