Not following Flight Plan KA350i [resolved]

[admin9]

Good Morning,

I have just bought this aircraft so new with it. I'm having an issue were the plane will follow the SID of the flight plan and then early in the flight the plane will then begin to turn right and just circle without going to the next way point. As seen in the pics FMS is set and Auto sequence is on. Can anyone please assist with were I am going wrong as I have tried everything I can to fix the issue. Thank you in advance. The FD is showing it should be turning left back onto the flight path but the aircraft goes right.

Have the latest update as I bought it after the update release. Also have the latest AIRAC 2006.

I am on p3dv4.5. Leaving ypad rwy 23 on the Bendo2 sid. Follows the sid from the runway around to the left like it should until it gets to that position the begins the right turn and continues it even if i try a DIR to another waypoint further on.

Photos attached.

[henrik.bergvin]

Did you by chance change airport location, time/date, or switch to the aircraft *after* another aircraft (or the KA) was loaded? This seems to be causing a lot of issues.

Also, your aircraft looks like it wasn't properly installed, looking at the font on the nav display...

[admin9]

Did you by chance change airport location, time/date, or switch to the aircraft *after* another aircraft (or the KA) was loaded? This seems to be causing a lot of issues.

Also, your aircraft looks like it wasn't properly installed, looking at the font on the nav display...

Hi, no was a single load with no changes. Did it yesterday also. It was bought and downloaded from orbx. Had the flat battery issue so installed the xmltools64 fix as per this forums which fixed that issue. Seems orbx download maybe faulty?

[lequinne]

I'm investigating this, thanks for reporting the issue!

[admin9]

I'm investigating this, thanks for reporting the issue!

Thank you please let us know.

[admin9]

I'm investigating this, thanks for reporting the issue!

For info: I did another test with MILVZ files and ORBS serial key and it did the same thing so not ORBX install this time. Its becoming quite annoying as i cannot complete this route.

[admin9]

Hello. Any update on this one please re testing?

[Taguilo]

Hi,

Just flew the same departure trying to replicate similar conditions. No issues at all, check the pics:

SID1.jpg (423.35 KiB) Viewed 2238 times

SID2.jpg (191.21 KiB) Viewed 2238 times

Are you using any addon scenery?


Tomas

[admin9]

Hi,

Just flew the same departure trying to replicate similar conditions. No issues at all, check the pics:

SID1.jpg


SID2.jpg


Are you using any addon scenery?



Tomas

Hi, thanks for that. How far did you go into that flight? Did you get past Bendo as its between murry and bendo it occurs. Although in the first pic it occurs earlier. Notice i also get the blue header line. I notice this appear before the right hand turn occurs.

Yes I do have add on scenery however i fly other non jets out of ypad using that sid (pc12 for example) and no issues so its not the scenery.

[Taguilo]

Hi,

All of the images you posted show references to BARKA-MURRY leg, not MURRY-BENDO.
I didn't continue past MURRY, sorry.

Could you please make another flight and post the correct images of where it is happening?

Thanks!

Tomas

[admin9]

No worries will do. It happens in between barko to bendo and it is in different places but appears in that area Ill get a video also of it occurring tomorrow which might make it easier to pin point something.

[admin9]

Okay so the good news is its fixed. It required a full reinstall of windows to fix it but it is now fixed. I am pointing towards the bad install from orbx and then trying to remove that and installing the files from milvz on top of it. Thanks for all the help.