Problem with new 1.1.8 built and axis calibration

[metzgergva]

Hi, I'm the PFC throttles and they require inverted axis assignments. So in the previous built I used 1.1.6 the folowing in FSUIPC to get the inverted axis:
[Axes.Turbo_2_Yoke_KA350]
RangeRepeatRate=10
0=0X,256,D,22,0,0,0 -{ DIRECT: Spoilers }-
1=1X,256,D,1,0,0,0 -{ DIRECT: Aileron }-
2=1Y,256,D,2,0,0,0 -{ DIRECT: Elevator }-
3=2X,256,D,28,0,0,0 -{ DIRECT: Rudder Trim }-
4=2Z,256,F,66420,0,0,0,*-1 -{ TO SIM: AXIS_THROTTLE1_SET }-
5=2R,256,F,66424,0,0,0,*-1 -{ TO SIM: AXIS_PROPELLER2_SET }-
6=2U,256,F,66423,0,0,0,*-1 -{ TO SIM: AXIS_THROTTLE2_SET }-
7=2V,256,F,66421,0,0,0,*-1 -{ TO SIM: AXIS_PROPELLER1_SET }-
8=2S,256,F,66422,0,0,0,*-1 -{ TO SIM: AXIS_MIXTURE1_SET }-
9=2T,256,F,66425,0,0,0,*-1 -{ TO SIM: AXIS_MIXTURE2_SET }-
10=3X,256,D,8,0,0,0 -{ DIRECT: RightBrake }-
11=3Y,256,D,7,0,0,0 -{ DIRECT: LeftBrake }-
12=3Z,256,D,3,0,0,0 -{ DIRECT: Rudder }-

I then had in MVAMS the throttle ranges assigned with INV ticked and set out the Max Reverse - Beta - Idle - Max Power. Same for the Prop Levers with Feather - Minimum - Maximum. Have been flying it for more than 2 month and all worked fine.
Today I installed 1.1.8, checked the settings in FSUIPC and in MVAMS, but the levers only run the "normal range", meaning I have no Max Reverse - Beta and no Feather.
Went through the process of assigning in FSUIPC and in MVAMS and I get the same data in the FSUIPC.ini and in the axis.cfg than before, but unfortunately not the right lever movements.

Could anybody help to find what is different on the V1.1.8???

Below is the content of the axix.cfg
[THROTTLE]
reverse=-16383
beta=-12348
idle=-9830
max=16383
invert=1
[THROTTLE1]
reverse=-16383
beta=-12663
idle=-9557
max=16008
invert=1
[THROTTLE2]
reverse=-16383
beta=-12647
idle=-9665
max=16383
invert=1
[PROP]
feather=-16383
min=-4587
max=16383
invert=1
[PROP1]
feather=-15968
min=-8364
max=16383
invert=1
[PROP2]
feather=-16176
min=-8814
max=16314
invert=1
[CONDITION]
off=-16383
lowidle=-4587
highidle=16383
invert=1
[CONDITION1]
off=-16383
lowidle=-4637
highidle=16383
invert=1
[CONDITION2]
off=-16383
lowidle=-4587
highidle=16383
invert=1
[GENERAL]
enabled=0

[Taguilo]

Hi,

To enable reverse operation please check REVERSE box in P3D axis configuration, leaving blank Inverse box in MVAMS.
Let me know if that works ok.

Thanks

Tomas

[metzgergva]

Thomas, due to multiple hardware controllers, I need to assign axis via FSUIPC and not in P3D. It was working with the shown settings up to version 1.1.6.

[metzgergva]

Hi, just restarted the PC and the sim, and now all works again. Happy to can fly her again.