Blackbird Sims / Milviz Forum Archive

I need some major help. I bought the KA305i this week and installed it into a clean install of the latest P3Dv4.5.13 and I am have major problems.
1. The main cabin door will not open when viewed from the inside or out
2. Elevator control yoke will not show inputs
3. All Engines control will not show inputs
4. Engine display is visible but will not show any input
5. Engines will not start when start switch is engaged
6. Props will not turn with engines on.
7. Engine covers and pilot will flash on than off when selected on
With the clean install the only extra software I have a registered copy FSUIPC. Orbx Base, Vector, openLC NA and Europe, Trees HD, Building HD, Airport Pack and Libraries, ChasePlane for view control.

Does your system meet the sim's requirements?
YES
Did you temporarily disable your anti-virus program during the download process?
YES
Before installing did you disable UAC. (User Account Control)?
YES
Did you install, and are you running the sim as an admin?
YES
Before running the sim did you make sure the FSX/P3D directory is off limits to any AV scanning?
YES
Does your system have the required distributables?
YES
Is your video card DX11 compatible?
YES
If applicable, did you disable any FSX to P3D migration tools (like Estonia) before running the sim?
YES
Are you using an aircraft other than a Milviz one as your default aircraft?
YES
Have you installed in the root sim directory?
YES
Do you have the appropriate SimConnect libraries installed?
YES

Aircraft: KA350i
Sim platform: P3D v.4
Operating system: Win10
Version: 191223
Unique ticket identifier: B581EB05-A62B-07F1-4A9C-EDA940EEFDAE

Michael

Have you installed HF2? And are you using FSUIPC to assign axes?

Best,
Peter

I have used FSUIPC to assign all axis, where is HF 2 found at?

doodlebug wrote: ↑

Sat Feb 29, 2020 7:17 pm

viewtopic.php?f=105&t=11651

Installed HF2 and still get no movement of any flight and engine controls or rotating props. I load the sim completely with the default F22 at KVPS than switched to the KA350. I get no visual response to any control inputs but the aircraft will increase engine power to all engine control inputs. Likewise Control inputs are displayed at the surface but not at the yoke or rudder peddles. If I load the aircraft straight from the menu the PBR textures are a super high gloss and nothing works.

Michael

Did you have a look at the topic about FSUIPC?

viewtopic.php?f=105&t=11513&sid=76499f1 ... 2d9be9746d

Peter

I had issues today when I tried to use the 350i after originally loading the default F22. Closed the sim and started again with the 350i from the start and it worked as it should.

qqwertzde wrote: ↑

Sun Mar 01, 2020 4:42 pm

Did you have a look at the topic about FSUIPC?

viewtopic.php?f=105&t=11513&sid=76499f1 ... 2d9be9746d

Peter

Peter,
Read it, tried it, and no joy

Michael

justinpaull wrote: ↑

Sun Mar 01, 2020 4:44 pm

I had issues today when I tried to use the 350i after originally loading the default F22. Closed the sim and started again with the 350i from the start and it worked as it should.

I tried it both ways and I either get an the doesn't work or a very shiny aircraft that doesn't work.

Hi,

These are the supported modes to run a KA flight:

1) From Scenario start page, select the KA, then select an airport, date, time, and run the flight.

2) Fron Scenario start page, load a KA saved flight, then if desired change the airport, date, time, and run the flight.

DO NOT:

- Select the KA from inside another aircraft's flight (using the menu).

- Select the KA from Scenario page after being loaded another aircraft.

- Change airport, date or time from inside a KA running flight, use the Scenario page for that.


Tomas

Taguilo wrote: ↑

Thu Mar 26, 2020 4:15 pm

Hi,

These are the supported modes to run a KA flight:

1) From Scenario start page, select the KA, then select an airport, date, time, and run the flight.

2) Fron Scenario start page, load a KA saved flight, then if desired change the airport, date, time, and run the flight.

DO NOT:

- Select the KA from inside another aircraft's flight (using the menu).

- Select the KA from Scenario page after being loaded another aircraft.

- Change airport, date or time from inside a KA running flight, use the Scenario page for that.


Tomas

Tomas,

That is how I load every flight for a Milviz acft or any other acft.

Michael

Hi I recently acquired a BE 350i. Extraordinary design. So I have 2 questions:

1. How do you open the door while being in the cabin
2. The FMS has an option to see the charts. After selecting the “charts” option, I hover around over the chart I would, ai click on “push/select”, but the chart disappears. I’ve tried several times, different ways from different views from the cabin. Do you have any suggestions. Does the aircraft app comes with charts? Do I have to obtain them separately?
Thanks lot for your time