King Air 350i Build 0.0.38

[Turbofandude]

Folks,

Build 0.0.0.38 is available here: King Air 350i Build 0.0.38.
As always, you will need a serial key to install and use the product. Oisín (doodlebug) or I can handle getting your keys. Please message one of us and we'll get you set up.

This build is approaching the final test version. Please test heavily and report items in this thread when issues are found. We expect the next build, or potentially the build after next, to be the final development build. At that point, we will begin asking testers to help us ensure it is ready for release and identify snags that would prevent that.

FAQ
Q: I can't install it without a serial key.
A: Message me or Oisín (doodlebug) for a serial key.

Q: I get SUPER low FPS.
A: Try disabling "transparent surface rendering" in the MVAMS.

Changes:
FMS Changes
-Fixed flight plan/legs operations not returning to the correct page index
-Fixed viewing arrivals for the departure airport incorrectly showing the arrival airport
-Fixed holes in FMS 2D bitmap
-Fixed MSG page header not displaying properly
-Fixed NO TXT WHEN PFD MAP display logic
-Fixed a number of missing legs
-Fixed transition display page index
-Fixed labeling of selected approach during transition selection
-Fixed discontinuity appearing at the end of a flight plan
-Fixed inability to enter consecutive segments of the same airway
-Fixed DEPART/ARRIVE right level 6 prompt displaying FPLN instead of LEGS
-Fixed excessive discontinuities when inserting SIDs/STARs/APPRs
-Fixed naming of CR legs
-Fixed naming of FD and CD legs
-Fixed alignment of "NONE" text on DEPART/ARRIVE pages
-Fixed RESEVSE FUEL typo
-Fixed FPLN page not properly isolating VIA/TO
-Fixed approach naming
-Fixed MISSED APPROACH appearing as part of the approach
-Fixed duplicate waypoint delete selection for terminal legs
-Fixed unneeded discontinuity when inserting legs
-Fixed ability to change the departure airport while airborne
-Fixed DEFAULTS not saving

Systems
-Added VNAV Climb phase
-Added AT/AT-BELOW/ABOVE-BELOW
-Various improvements

PL21
-Fixed a minor memory leak
-Fixed a CTD relating to FMS procedure insertion

Other Changes
-added missing RTU font
-corrected Texture.cfg

Visual
-Various model fixes
-Various texture fixes
-New liveries

[gregmorin]

I did quick check it out flight

1. Nose wheel and rudder animation is INOP. The aircraft responds to the rudder inputs but the visual nose wheel and rudder do not. They are stuck in the full left position.

2. The reverse sound is weird. I get a pulsing sound.

Greg

[Razor6666]

Same here on the locked nose wheel and rudder locked left position.

[Raptor]

FMS is not adding waypoints, although they are showing in the MFD

Reporting in Mantis

I also have the locked nose wheel and rudder

[mongo501]

Hi: Two issues to report. I'm learning how to use the PL21, so I don't have the nomenclature down. When I clicked on the second from the top right button on the PFD (next to the entry for Rdr/Terr) I got two CTDs. The first time was on the ground. The second time was in the air. While flying, after I was able to start up the radar, I clicked on the button and crashed the program. Also, I have the full deflection of the nose wheel and rudder to the left. Hope this helps. Mike Gutierrez, North Hollywood, California.

[ega]

Same here on the locked nose wheel and rudder locked left position.

If possible, could you please provide a hotfix to clear this issue?

[baldk9]

Go along with the nose wheel, the engine deice is on at start up, along with a very loud fan noise. On mine the autopilot was inop.

[abiliomanuel]

Hi

1.Same issue nose wheel and rudder...
2.Engine Anti-ice not iluminate..
3.Electrical system test on first stage with battery only antil flaps check.. work better on v0.0.37

[N4GIX]

Same here on the locked nose wheel and rudder locked left position.

Tomas hasn't added the custom nosewheel & rudder code yet.

[giorgio759]

Thanks for the update. The new liveries look really good! I did have a few problems, however.

1. FMS (entering legs): I was able to enter the 1st waypoint on the 1st flt pln page, but on the 2nd page waypoints weren't displayed after clicking on the RSK. But everything I entered on the 2nd flt pln page (whole flt pln) did display properly on the Dir and Legs pages despite not displaying on the flt pln page.

2. Autopilot (following flt pln): During climb-out I enabled the AP and HDG mode. No probs. Switched to NAV & the aircraft began wandering left and right until it drifted left and continued in a circle. Reenabled HDG mode, but was unresponsive. Tried NAV & HDG alternately a few times, but no joy. No response. Lateral modes seemed disabled. It reminds me of the problem I had in 0.0.33.

3. Master Warning & Caution lights do no illuminate while flashing. They turn dark rather than illuminate.

4. Prop Sync/Emer Freq switches do not illuminate when enabled, but turn black.

5. I'm also experiencing the various problems that have been posted by others in this thread.

Thanks,
George McDowell

[rayharris51]

Hi

SID STAR entry seems fixed which is great.
Radar key caused a crash again so I’m not initiating it until it is fixed I guess.

Error message came up when selecting RW36 sSTAR into NZRO:
SOCIETY ODBC error.....
Microsoft Access driver missing

Same issues as others report as far as I’ve been able to tell, notably stuck nose wheel.
Noted the custom code isn’t there but nose wheel was straight in the previous version I think
Thanks

Ray

[Heronjr]

+1 fms flight plan enter issues, front gear wheel position fixed, and crashes. V37 is more stable.

Regards

[tamsini]

Can't wait for Friday night!!!!

Mario

[rayharris51]

Apologies ‘helpful’ spell checker override.

I meant SOC ODBC error when entering REEVE1 STAR to NZRO RWY18. No crash though.

[giorgio759]

Hey, here are a few screenshots of problems I mentioned in a previous post plus another problem I didn't mention:

Master Caution/Warning lights:

Master Warning-Caution-edited.jpg (824.72 KiB) Viewed 2123 times

Prop Sync & Emer Freq lights:

PropSync-EmergFreq-edited.jpg (841.91 KiB) Viewed 2123 times

Entry Door textures & object misplacement:

Exit-editedjpg.jpg (543.43 KiB) Viewed 2123 times

Thanks