Can't follow flightplan using NAV mode/FMS source

Post by **Taguilo** » Mon Dec 23, 2019 2:57 pm

Because NAV mode uses aileron inputs to minimize Crosstrack error on current leg (XTK)
It is a custom AP, some functions are independent of P3D defaults.

Anyway, glad that it worked for you.

Tomas

Post by **JonathanBleeker** » Mon Dec 23, 2019 6:03 pm

I have asked Brunner about a possible solution to make it fully compatible with our simulation but they are closed for the holidays till Jan 5. Will see what comes up then.

Regis9 · Post by **Regis9** » Mon Dec 23, 2019 6:12 pm

Thanks guys, hopefully Brunner can figure something out.

Post by **JonathanBleeker** » Wed Jan 08, 2020 3:52 pm

Sorted. Spoke to Brunner and gave them the solution and they will be trying it out after the 27th.

Regis9 · Post by **Regis9** » Thu Jan 09, 2020 12:03 am

Great news, I appreciate that the Brunner yokes are a bit of a niche piece of hardware so I really appreciate your efforts to sort this out with them.

So if the fix works on their end, will that be something they send out or would it come in a future service pack from Milviz?

Post by **JonathanBleeker** » Thu Jan 09, 2020 7:58 am

It’s on their side. I described how to send the desired events without overwriting our AP

Regis9 · Post by **Regis9** » Thu Jan 09, 2020 12:02 pm

Perfect, thanks again.

didier · Post by **didier** » Wed Jan 22, 2020 12:02 pm

Hello,
Thank you Regis9 for posting this. I have the same problem and just tried a flight configuring CLS2Sim to "Emulate USB HID joystick". It worked nice.
I tested the DA62 too and finally got it to follow the flight plan. I need to test with a couple of models but I'm quite sure that you gave me the right input!

Obviously I've just created a ticket on Brunner's Helpdesk.

j.waeber · Post by **j.waeber** » Wed Jan 22, 2020 12:19 pm

Just read the thread. I'm in the same boat. I also own a cls yoke including their rudder pedals. But i didn't fly the king air yet, since my external throttle quadrant is not working. Waiting for the hotfix/service pack. I would appreciate any updates regarding the brunner controls.

Regis9 · Post by **Regis9** » Tue Feb 04, 2020 1:41 am

Curious if there was ever any words back from Brunner on how their testing went?

Post by **JonathanBleeker** » Tue Feb 04, 2020 2:57 pm

I imagine they will release an update when that happens.

Regis9 · Post by **Regis9** » Sun Mar 01, 2020 2:09 pm

As a brief update, I emailed Brunner asking about this and posted on their forum and have not received a response (which is odd, they’re usually very responsive).

As a workaround for anyone with a Brunner yoke, last night I completed a flight by going into the Brunner software and disconnecting the yoke from the sim once I had the autopilot on. Doing that it followed NAV just fine. Not the best workaround, but something until Brunner issues a fix.

didier · Post by **didier** » Tue Jul 28, 2020 2:15 pm

A few month later... using CLS2Sim v4.27.6 (that is last version) I'm still obliged to use it as a (stupid low cost) "USB HID joystick" because

Brunner software is not updated.

Am I missing something? Did one of you have a nice solution? Thank You.

Blackbird Sims / Milviz Forum Archive

Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source

Re: Can't follow flightplan using NAV mode/FMS source