Weapons not showing on aircraft F 4E

[kvngentile]

Hello i was just in contact with someone on support for the F 4E , just received an updated version on Aug 23, 2018. worked fine for a day but later ,when i got to load the weapons, i see none loaded on the F 4E . I have both corresponding Tacpak for the Fo4E. Tackpack is on. Just stopped working . and anyone help with this . Thank you.

[kvngentile]

This is the error message im getting about the F 4E dll module for the NVAMS .

Note pad error.jpg (401.2 KiB) Viewed 4050 times

[kvngentile]

Ok done a system restore Aug 25,2018 ,now the aircraft is once again showing in the MVAMS, but still NO payload is showing the F 4E when weapons are selected. The selections are made ,and dragged and dropped on the pic ,in the window. Nothing happening. Can i get any help .Thank you.

[JonathanBleeker]

Uninstall the F-4E, then reinstall in the following order:

Base package
TACPACK integration package
ADV package (if you have it)

[kvngentile]

ok going to do this. and i do not have the ADV model . Also i already had VSR tacpack ,was it necessary to get the Milviz one for $14.00 . If these are the same packs i installed both.

ok i searched for the Phantom II tacpack and the only thing showing is the installer. Its as if it never loaded. Also when i click the installer to uninstall ,it just goes forward as if it will in install to a new folder or destination. As i mention before the only Tacpack i see on my computer is the VRS Tacpack. Would i have to uninstall that one?
ok. uninstalled the VSR tacpack install the F 4E then reinstalled the VSR tacpak ,ant still no load out Could not find the Phantom II tacpack v A1 180712 on the computer anyware.

[JonathanBleeker]

The Milviz TACPACK integration package is what integrates VRS TACPACK into the Milviz F-4E (As I understand, you bought both from FSPilotShop?). Only the base package has the uninstaller check box in the installer. So run the base package installer first.

I believe doodlebug/Oisin sent you the latest installers?

[kvngentile]

Yes Osh sent me the latest installer. Now when i run the installer , I select the sim version FSX SE then i select the Uninstall and the End Users License Agreement pops up. Once i click accept , the intallation window pops up asking what folder i want to install to . By the time i get to this point the F 4E is still in the FSX folder. here are some screen shots. and should i continue with the process.

[JonathanBleeker]

The ETP indicates that you are running the TACPACK installer, not the base installer when you try to uninstall. The base installer is a much bigger file than the TACPACK installer.

[kvngentile]

I truly believe i do not have the base Installer , When i ordered the the tacpack from FSPilotshop , that ETP installer is all that came in the zip file.

[kvngentile]

Here's a screen shot of what was inside the zip.

[JonathanBleeker]

Wait, I am a bit confused now. Didn't you buy the original F-4E before you bought the TACPACK package?

[kvngentile]

Yes but it was and Older model . Osh gave me an email with an downloadable link ,with the latest F 4E v A1 180712 , the tacpack i got from FSpilotshot has the same version numbers. The first F 4E i had on FSX SE was version A1 150803SE.

[JonathanBleeker]

Download the installer that Osh sent you and run that first. Can't do anything with the ETP installer until you have uninstalled and reinstalled with the base pack.

[kvngentile]

OK i have done that i ran the installer for the F 4 that Osh sent. uninstalled and reinstalled it. Then i did the same for the ETP uninstalled and reinstalled it. Still not weapons showing on the F 4E in sim.

[kvngentile]

Ok after working with it more errors came up. Went back to the first screen shot as posted earlier. This after another system restore ,didnt an caouldnt go back far enough.