Blackbird Sims / Milviz Forum Archive

Dear friends,

I know you´re working a lot with the F-4, but I´m getting more and more frustated,I got this morning the new update, F-4SJ Phantom II vA1.170426_JS, disable A/V,Run as Admn,etc.etc. Installed it and CRASH again... My goodness there must be something very wrong with this product.I´m a simmer since 1996 and I have several addons like VRS FA-18 w Tacpack,FsLabs A320,PMDGs, CaptainSim Tristar,AS16,etc. and no problem at all.

The fault Msg is:

Problem signature:
Problem Event Name: BEX
Application Name: Prepar3D.exe
Application Version: 3.4.22.19868
Application Timestamp: 588f7cbf
Fault Module Name: MSVCR90.dll
Fault Module Version: 9.0.30729.4940
Fault Module Timestamp: 4ca2ef57
Exception Offset: 00031484
Exception Code: c0000417
Exception Data: 00000000
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1046
Additional Information 1: daeb
Additional Information 2: daebfec1df455cd9d5b469989c09f8ef
Additional Information 3: dc41
Additional Information 4: dc411c903a4857ea67b7313558648dd7

Please help me!

I just ran the F-4J/S installer this side for P3D v3.4.22 (I uninstalled first) and it works fine. You might be getting the issue where the installer doesn't overwrite properly. Try Uninstalling completely, and then reinstalling.

JonathanBleeker wrote:I just ran the F-4J/S installer this side for P3D v3.4.22 (I uninstalled first) and it works fine. You might be getting the issue where the installer doesn't overwrite properly. Try Uninstalling completely, and then reinstalling.

I completely deinstall my NOD32 A/V ,install again vcredist_x86.exe and DirectX, run DX Diagnose, no problems found.


Then I uninstalled completely the F-4 S/J and then reinstalled ,start P3D, when I load the F-4 J or S CRASH with that same fault msg: MSVCR90.dll

When does the crash occur? After loading while the engines are spooling up or before?

JonathanBleeker wrote:When does the crash occur? After loading while the engines are spooling up or before?

Something odd happened,as I said before, I deinstall A/V and whole F-4, reboot (twice) and when I start P3D, crash. I turn off the PC and back home 2 hours later. When I saw your question above,I decide to check if the crash was before or during spolling up. (I remember was before) but to confirm and answer you correctly I start P3D... Guess what ?? NO CRASH for the first time. I had no idea what happened since the PC was off. Now I´ll try to install the A/V again.

And please what´s the recommended setting for P3D sensitivity and null zones ? (For example,VRS asks in its manual Max sensitivity (127) and 1 for null zone) I use TM Warthdog stick and Hotas.

Thank you !

I use the same settings but I don't think it is particularly specific.

Hi,

My F4E also crash when I try to start the engine with the new update (vA1.170424)!
Have to return to vA1.161120 version.... with my P3D v3.4.18.19475 !

BugDani.

To profit from the new update you would need to have either P3D v3.4.22+ or P3D v2.5 (latest version) or FSX:Acc or FSX:SE

doodlebug wrote:To profit from the new update you would need to have either P3D v3.4.22+ or P3D v2.5 (latest version) or FSX:Acc or FSX:SE

Thanks! Ugraded, now it work ! Sorry for disturbance.